Wright Manufacturing Mower Manuel d'instructions

1 HYDRO PISTOL GRIP Instruction Manual Wright Manufacturing 4600X Wedgewood Blvd Frederick, Md 21703 Velke PG serial 54956 and higher WA

10 WARNING WARNING WARNING WARNING • DO NOT allow inexperienced persons to operate the mower until they have read and understood thes

11 WARNING 1.15 Operation on Slopes DO NOT operate on steep slopes. Do not operate the mower on slopes steeper than you can feel secure about the

12 WARNING WARNING WARNING 1.16 Fuel Safety Handle gasoline with care – it is highly flammable. Do not smoke while handling gasoline.

13 2 Warning, Safety and Instructional Decals • Specific safety warning decals are located on the equipment near immediate areas of potential haz

14 ApplicationThread LockerTorque Range (ft-lbs)Wheel motor bolts Loctite 2760 40-50 / 54-68 NmClutch to engine shaft Loctite 2760 50-55 / 68-75 NmWh

15 4 Machine Description & Overview The Wright Velke Hydro Pistol Grip is meant to solely cut, bag or mulch grass. The use for any other purpose

16 4.1 Operator’s Area 1.Steering / Brake Lever 2.Neutral Latch Lock 3.OPC Paddle 4.Velke Sulky Release 5.Speed Control Knob 6.Control Linkage 7.Velk

17 4.3 Control Panel & Steering Control Levers The Velke Hydro Pistol Grip speed and direction are controlled by releasing and squeezing the stee

18 4.6 Safety Interlock System The Wright Velke Hydro Pistol Grip is equipped with a safety interlock system. The PTO must be disengaged, speed adju

19 WARNING WARNING 5.2 How to Start the Mower Read and understand the safety instructions before attempting to operate your machine. Use

2 Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you advanced engineering and qua

20 WARNING WARNING 5.4 How to Drive the Mower Over a Curb To climb a curb, first see the Safety Instructions section of this manual, especi

21 WARNING The wheels should now go to a neutral position if the steering control levers are locked using the thumb locks and/or the speed contr

22 WARNING 6 Service and Adjustments 6.1 Tire Maintenance and Pressure Excessively worn tire tread is dangerous on all hills. Replace drive ti

23 WARNING 6.3 How to Move the Mower if the Engine Won’t Start Rotate both of the hydro bypass valve levers on the side of each hydraulic pump a

24 6.7 Lubrication Grease with No. 2 general purpose lithium base or molybdenum base grease. • Set parking brake, stop the engine and remove the key.

25 Assembly hole Threaded Removal holes Assembly hole 6.10 Spindle and Drive Pulley Split hub R&R • Remove 2, ¼” bolts from split hub and install

26 •Temporary Height-of-Cut Adjustment: Using the caster shims (or spacers) you can adjust the blades downward temporarily .5

27 Max Fill 6.13 Fuel Evaporation System All Wright Velkes need to have this mandatory feature. •Do Not alter or remove •Do Not fill past the “Max Fi

28 6.16 Cleaning the Mower The underside of the mower deck should be checked and cleaned twice daily and more often if the grass being mowed is lush

29 7 Component Breakdown

3 Table of Contents PRE-DELIVERY SERVICE OF MOWER BY DEALER ...

30 8 Electrical Schematics

31

32 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks

33 Date Maintenance/Service PerformedUnit HoursShop/TechnicianMaintenance Record

34 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document wi

35 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The United States Environmental Protection Agenc

36 (3) Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the period

37 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades ar

38 NOTES:

39 NOTES:

4 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual i

40 4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com

5 or in its line of discharge at this or at any time. The discharge chute deflector should be in the down position.  Move the engine throttle contr

6 1 Introduction This mower is built to the highest standards in the industry. However, carelessness or operator error may result in serious bodily

7 Do's Don'tsRead the operators manual before attempting to operate this machine Don't disable safety switchesUse all PPE's, eye

8 WARNING WARNING WARNING WARNING WARNING 1.3 Important Information It is vital that these instructions are available to machine

9 WARNING WARNING compromise operator safety, shorten equipment life and void your manufacturer’s warranty. Keep all nuts, bolts, and screws